Accessories
| Series 160 - Disposable Plastic Spiral Bell Mixers Click here for table of sizes available |
With conventional meter-mix manifolds reactive materials can meet
within the manifold before it reaches the mixer. This can cause costly
and time-consuming blockages. The series 160 with it's oversized bell
inlet allows manifolds and valves to separately port the A and B
materials directly into the mixer. It also makes clean-up a breeze.
Simply remove the mixer and wipe the manifold face clean.
within the manifold before it reaches the mixer. This can cause costly
and time-consuming blockages. The series 160 with it's oversized bell
inlet allows manifolds and valves to separately port the A and B
materials directly into the mixer. It also makes clean-up a breeze.
Simply remove the mixer and wipe the manifold face clean.
| Series 160, 260 Luer Needles Click here for sizes and styles available |
We offer two types of Luer Needles - standard and tapered. The
standard needle features stainless steel tubing with a burr-free blunt
end and plastic hub. The tapered needles is a one-piece, plastic
molded part. The needles are color-coded and pre-packaged with 50
needles per bag.
standard needle features stainless steel tubing with a burr-free blunt
end and plastic hub. The tapered needles is a one-piece, plastic
molded part. The needles are color-coded and pre-packaged with 50
needles per bag.
| One Piece Metal Jackets Contact us to order this product. Click here. |
For medium and high-pressure systems, it is recommended to use a
metal jacket over the mixing nozzle. We offer a range of low-cost,
one-piece jackets. They are ideal for robotic applications where
repeat positioning is required. All manifolds and valves have a
standard 7/8 x 14 thread, but our metal jackets are offered in both
standard and an alternative 7/8 x 9 thread for your convenience.
metal jacket over the mixing nozzle. We offer a range of low-cost,
one-piece jackets. They are ideal for robotic applications where
repeat positioning is required. All manifolds and valves have a
standard 7/8 x 14 thread, but our metal jackets are offered in both
standard and an alternative 7/8 x 9 thread for your convenience.
| 400 & 450 Series Autovalves For full product information - Click here. |
Series 400 & 450 autovalves are easy to clean and offer features like
optional stainless steel valves, flush valve manifolds, lubricated and
hard coated pistons, optional Polytuff, Teflon, Viton, and EP seals and
the optional Night Cap and Ratio Check Caps.
optional stainless steel valves, flush valve manifolds, lubricated and
hard coated pistons, optional Polytuff, Teflon, Viton, and EP seals and
the optional Night Cap and Ratio Check Caps.
| Series 400 & 450 Manifolds For Available Styles - Click Here |
Our two-component manifolds separately port the resin and hardener
into the mixing nozzle. Cleanup simply involves wiping the manifold
face after the nozzle has been removed. To prevent back flow or cross
contamination of reactive material, in-line check valves are available.
into the mixing nozzle. Cleanup simply involves wiping the manifold
face after the nozzle has been removed. To prevent back flow or cross
contamination of reactive material, in-line check valves are available.
| Night Cap & Ratio Check Caps Click Here for These Items |
We Offer Teflon Night Caps and Ratio Check Caps with nuts for use in
conjunction with our manifolds and dispensing valves.
conjunction with our manifolds and dispensing valves.
| Series 550 Low Pressure (LP) Valve For Part List - Click Here. |
The inexpensive Series 550 LP Valve is intended for low pressure
meter mix applications. This manual valve is ideal for dispensing
beads or RTM casting. The design is simple: two ball valves are
threaded into the back of the manifold and are connected to a
common lever so that both valves open and close at the same time.
The A and B fluids are separately ported through the valve and do not
meet until they enter the mixing nozzle. Cleanup is simple: just remove
the mixing nozzle and wipe the manifold face clean. Three manifold
styles are offered: Low Flow, High Flow, and Wide Ratio.
meter mix applications. This manual valve is ideal for dispensing
beads or RTM casting. The design is simple: two ball valves are
threaded into the back of the manifold and are connected to a
common lever so that both valves open and close at the same time.
The A and B fluids are separately ported through the valve and do not
meet until they enter the mixing nozzle. Cleanup is simple: just remove
the mixing nozzle and wipe the manifold face clean. Three manifold
styles are offered: Low Flow, High Flow, and Wide Ratio.
| Series 600 High Flow Manual Dispense Valve For Part List - Click Here. |
The Series 600 "MEGA" Valve was designed to take full advantage of
the high flow rate/high viscosity mixing capabilities of the series 162A
Disposable Mixers and allow the user to handle both material types
easily. A and B components are separately ported through the valve
and don't combine until they meet inside the static mixer.
the high flow rate/high viscosity mixing capabilities of the series 162A
Disposable Mixers and allow the user to handle both material types
easily. A and B components are separately ported through the valve
and don't combine until they meet inside the static mixer.
| Series 442 Dynamic Manifold For More Information - Click Here |
The unique design of the series 442 Dynamic Manifold combines
dynamic mixing with low-cost, disposable mixing chambers. This
system is ideal for casting and molding application such as RTM,
potting and encapsulation, and for difficult to mix urethanes and
epoxies.
dynamic mixing with low-cost, disposable mixing chambers. This
system is ideal for casting and molding application such as RTM,
potting and encapsulation, and for difficult to mix urethanes and
epoxies.
 |
 | |  | |  | |  | |  |
